About this download

File Info

File Name

• HVL-F60RM2 System Software (Firmware) Update Ver. 2.00 (Mac)

File Version

• 2.00

File Size

• 1.5 MB (1 457 084 bytes)

Release Date

• 10-01-2024

Preparation

Check the system software version

Follow the instructions below to check the system software version. If the system software version is Ver.2.00, the update is not required.

1. Select Menu → 2/2 → VERSION → FLASH on the device.
   
2. The system software version is displayed.
   

System Requirements

Operating Systems

The latest version of the system software update is compatible with the following Macintosh versions:

• macOS 11, 12, 13

Computer Hardware

The latest version of the system software update is compatible with the following hardware:

• Hard drive: 600 MB or more
• RAM: 512 MB or more

Other Hardware

• Power source for the device:
  Four new LR6 (AA-sized) alkaline batteries, or four fully charged AA-sized rechargeable nickel-metal hydride (Ni-MH) batteries.
  Note: The update can be performed only when the remaining battery level is enough. We recommend that you use new batteries or fully charged batteries.
• Use Micro USB cable compliant with USB standards.
  Note: Update functionality is not guaranteed with any other USB cable.

Download & Install

Important Notice

• Use four new LR6 (AA size) alkaline batteries or four fully charged AA-sized rechargeable nickel-metal hydride (Ni-MH) batteries.
• Do not remove the battery during the update; otherwise, the device may become inoperable due to the sudden power shutdown.
• Prevent the computer from entering Sleep mode.
• Ensure all devices except the computer are disconnected.

Install the Driver:

Please do these operations while connected to the Internet.

When updating this device, the Device Driver provided by Silicon Labs is required. Download the following file.

1. Visit the Device Driver download page and download the Device driver (Silicon Labs).
2. Click the Download button.
3. After reading the disclaimer, click Download.
4. Save the file to the desktop of your computer (recommended).

How to Install the Device Driver:

1. Double-click the downloaded file SiLabsUSBDriverDisk.dmg. Do not connect the device at this time.
2. Silicon Labs VCP Driver Install Disk folder is displayed.
3. Double-click the Install CP210x VCP Driver in the folder.
4. The installer screen is displayed. Click Continue to proceed.
   
5. The software license agreement screen is displayed. Click Agree.
   
6. Permission to install the helper tools will be required. Enter the password when you log in with an administrator account.
   
7. Once the extension is blocked, open the Security & Privacy system preferences.
   
8. Click the key in the Security & Privacy system preferences and select Allow.
   

How to download the Updater:

1. Make sure that you are logged on as a user with administrative rights.
2. Click the Download button above.
3. After reading the disclaimer, click Download.
4. The Update_HVLF60RM2V200.dmg file will start downloading.
5. Save the file to the desktop of your computer (recommended).

Step 1: Start the Updater

1. Close all current programs running on your computer.
2. Double-click the downloaded Update_HVLF60RM2V200.dmg file. Do not connect the device at this point.
3. Update_HVLF60RM2V200.dmg is expanded.
4. Double-click the SystemSoftwareUpdater icon.
   
5. To load a kernel extension, the message prompts you to allow the application to make changes. Type the password for the administrative account.
   
6. System Software Updater starts up.
   
7. Turn on the device.
8. Use a USB-standard cable or USB cable attached to the camera. Then connect the computer and the device. USB CONNECT will be displayed on the LCD panel when it is connected to the USB cable.
   
   
   Note: If the computer cannot find the device, the message Could not find the device for this update. appears on the computer display. Try the following if this happens.
   • Disconnect the USB cable and connect it again.
   • If the computer has multiple USB terminals, try with the other terminals.
9. After confirming the LCD panel for the device, click Next. The current version and the version after the update appear on the lower left part of the screen. After confirming the Current version is Ver. 1.00, click Next.
   Note: If the current system software version is Ver. 2.00, the update is not required.
   If this is the case, stop the USB connection and click Finish, turn off the device, remove the battery pack, reinsert the battery, and turn the device back on.
   • An update is required
     
   • An update is not required
     
10. The device automatically resets.
    
    Note: Loading icon may not be displayed depending on the OS version being used.
11. Start the update. After automatically resetting, the following screen appears and the update starts. The progress bar appears while updating (approximately 10 minutes).
    Note: Never turn off the device or disconnect the USB cable while updating.
    
12. Complete the update. Once the update is complete, the screen below will be shown.
    Note: The device will automatically reboot, which may take a few minutes. When the screen appears, press the Finish button and disconnect the USB cable. Please turn off the device and turn it on again.
    

Step 2: Confirm the system software version of your device is Ver.2.00

1. Select Menu → 2/2 → VERSION → FLASH on the device.
   
2. The system software version is displayed.