SEL85F14GM Lens System Software (Firmware) Update For Mac OS

Details

Important notes:

• This Lens system software update can be performed only when the lens is attached to the camera. You cannot perform the Lens system software update using other camera.
• Attach the lens to the camera before performing the lens system software update. Make sure the camera is turned off.
• When performing the lens system software update, please use a fully charged rechargeable battery pack or the dedicated AC adaptor (sold seperately).(for α Interchangeable-Lens Camera)
• When performing the Lens system software update, please use the dedicated AC adaptor.(for Camera – Broadcast & Production)
• Do not remove the battery during the update; otherwise, the camera may become inoperable due to the sudden power shutdown
• Remove the memory card from the camera beforehand
• Prevent your computer from going into sleeping mode. In case the computer would go into sleeping mode and the update would be interrupted, redo the complete update process from the start

How to download the lens system software updater:

1. Read the disclaimer and agree to the terms and conditions by clicking on the checkbox. Then, click on theDownloadbutton.
2. The download of the [Update_SEL85F14GMV2D.dmg] file will start.
3. Save the file to the desktop of your computer (recommended).

Once the file has downloaded successfully, you're ready to install the lens system software update Ver.02 for SEL85F14GM.

Step 1: Start up the lens system software updater

1. Double-click the [Update_SEL85F14GMV2D.dmg] file you downloaded. - Do not connect the camera at this point.
2. Double-click the [Update_SEL85F14GMV2D] icon which appears on the Desktop.
3. Double-click the [Lens system software Updater] icon.
4. To load a kernel extension, the message prompts you to allow the application to make changes. Type the password for the administrative account.
   
   
5. The lens system software updater window appears.
   
   
6. Turn on the camera. If the camera has already been turned on, turn it off and then turn it on again.
   According to the instruction on Lens System Software Updater, select [Menu] → [Setup] → [USB Connection] on the camera, and checkif [Mass Storage] is selected. (If you are using the QX series, this step is not necessary.) If the mode other than [Mass Storage] is selected, please select [Mass Storage].
   
   
7. Remove the memory card from the camera beforehand. Connect the camera to the computer with the supplied USB cable.
   If an error message appears on the computer screen, please try the following methods.
   - Disconnect the USB cable from thecamera, then reconnect the USB cable.
   - If there are another USB terminal with the computer, reconnect the USB cable to another USB terminal.
8. Click Next on the lens system software updater. The lens system software updater window appears on the computer and "Follow computer instructions." appears on the camera screen.
   Computer:
   
   
   
   Camera:
   
   
   
   Note: From now on, never turn off the camera until the Lens system software update is completed.
   Itmight takes a few minutes to screen changes depending on the camera model.
   • If the messsage "The update is not available for your model." appears, check if the system software file you're trying to install is the correct file for the lens which is attached to your camera.
     In case the correct lens system softwareupdater is running, close the updater, disconnect the USB cable, turn off the camera, and go back to step 1 "Start up lens system software updater".
   • If the message "Could not find camera with the lens for this update mounted." appears, check if your camera is listed in the "Relevant Products" section and if the camera is connected to the computer with USB cable.

Troubleshooting:
9. Click Next on the lens system software updater. The current version and the version after the update appear on the lower left part of the screen. If the current lens system software version is .02 or later, the update is not required. In this casestop the USB connection and click Finish, turn off the camera, remove the battery pack and/or the AC adapter, reinsert the battery or reconnect the AC adapter and turn on the camera.
   
   Update is required
   
   
   
   Update is not required
   
   
10. Confirm [Current version] is .01, click [Next]. The data is being transferred to the camera (approximately 5 seconds).
    Note: Never turn off the camera nor disconnect the USB cable while updating.
    
    
11. When the data transfer is finished, the following screen appears:
    
    
    
    Click Finish.
12. The update process starts and the progress bars is displayed on the camera (approximately 30 seconds).
    
    
13. The update process is finished when the "Lens update complete." message is displayed on the camera.
    If you are using the QX series, the update process is finished when the screen of the QX series disappears.
    
    
14. Disconnect the USB cable.
    Note: After finished the update, turn off the camera, remove the battery pack and/or the AC adapter, reinsert the battery or reconnect the AC adapter and turn on the camera.

Step 2: Confirm the lens system software version is Ver.02.

1. On the camera select Menu → Setup → Version.
2. The lens system software version is displayed as illustrated below.